The first thing I'm going to do is configure the speeches with their names and configure the interfaces
as trunks or access ports.
That means we need to configure the villains on the switches as well as configured the VTB mode.
This is the console for switch one.
So in other words Iowas V L to and one as you can see here in the console
Monotype been able to go to privilege mode top confetti to go to global configuration mode and then
type hostname and I can specify the name of the switch.
I'm going to configure it as a as one do allows me see show commands in global config mode as an example.
So I'm going to use the command to show IP interface brief to view interfaces on the switch so I can
see various interfaces such as gigabit 00 gigabit 0 1 and so forth which have a status of up up at the
moment in the apology I'm only using gigabit.
0 0 2 gigabit 0 3 as well as gigabit.
One slash is zero.
So these are the interfaces that I'm using as a base practice I'm going to shut down any other interfaces
on the switch so I'm going to shut down gigabit once one two three my interfaces have gone down.
So do show IP interface brief shows me that those interfaces are currently down.
I should also shut down to select 0 two three
as well as three slash is zero two three so do show IP interface brief
shows me that those interfaces are shut down.
Now you probably want to script this kind of configuration.
So on the other switches all do most of the configuration through note pad and then simply paste it
into the switch console's to speed things up.
But what we've done at this point is shut down unused interfaces and we've named the switch the range
command is really useful when doing configurations on multiplying two faces by default.
We have a villain one configured as well as a legacy villans such as one thousand two three four and
five which are used in the past for DGI and Token Ring villaine one is the only villaine used in an
Ethernet environment in the apology.
However I need to configure a violent 10 as well as violent 20.
Now before I configured the Villines I'm going to change the ETP mode to transparent so that every switch
uses its own local database of villans by default the VIP mode is set to server and we can see that
by using the command show VTB status servers allow you to create villains and they also synchronize
with other switches in the topology.
I don't want to do that so I'm going to type the VCP mode transparent so that my switch does not try
and synchronize with other switches in the topology in a small environment like this.
We don't really need VTB and VTB can cause a lot of problems in networks.
So for safety reasons I'm going to disable ETP and the command show VDB status allows me to see that
the mode is now changed to transparent.
The number of existing villans is five.
The maximum number of villans supported in the switches 1005 we can see the current villans wiretapping
show villans once again.
And as you can see we have one one thousand two three four and five as the five villans currently configured
share VDB status shows me that the switch supports of ETP modes.
One two three.
The current version running is of ETP one.
The switch is not part of a VTB domain.
We can also see that VTB pruning and VTB trapped generations are disabled.
So show villaine brief shows me that I have villaine one configured and all of these ports are in the
land one the land one is the default.
Ethan had Bil'in once again and all interfaces are by default in villaine one so confetti violent 10
and 20 and show V LAN brief.
Now you can see that movieland 10 and villaine 20 have been created and added to the list of villains
currently available on the switch for support to be put into a villain the villain needs to be added
to the villain database.
So if I was going to put this NPM server into violent 30 as an example I would need to configure violent
30 and then add to that port to violent 30.
In this example I want to configure VLAN 10 ENVI land 20 because I'm going to create a layer 3 interfaces
on the switch for those villains.
So I need to have configured the villains in the villain database first.