1
00:00:00,900 --> 00:00:10,260
Now to do the integration with Janus 3 on my VM and this is my NPM VM I'm going to change the network

2
00:00:10,260 --> 00:00:18,910
adapter to use a VM net one host only on my physical machine.

3
00:00:19,070 --> 00:00:25,620
I have two VM net adapters a VM net one and VM net eight.

4
00:00:25,640 --> 00:00:34,010
Previously my virtual machine was bridged to the physical adapter but to allow it to be controlled by

5
00:00:34,010 --> 00:00:39,980
genie 3 I'm going to change it to VM net one host only.

6
00:00:39,980 --> 00:00:50,760
I'm also going to change firewall settings and turn off the firewall so that I can ping the virtual

7
00:00:50,760 --> 00:00:54,390
machine from my genius three routers.

8
00:00:54,580 --> 00:00:57,530
That'll just make it easier in the lab to do testing.

9
00:00:59,590 --> 00:01:07,000
What I also need to do is shut down the virtual machine so that genius 3 can control it.

10
00:01:07,150 --> 00:01:16,030
So once again I've shut the machine down I've gone to network adapter settings and set it to use host

11
00:01:16,030 --> 00:01:28,050
only and I've disabled to the firewall what I'll do now is take a snapshot so that I can revert to it

12
00:01:28,060 --> 00:01:29,730
if there are any problems.

13
00:01:29,830 --> 00:01:40,790
So NPM installed I did that quickly and made a mistake so I'll go to VM snapshot manager and change

14
00:01:40,850 --> 00:01:46,310
the name to NPM installed.

15
00:01:46,350 --> 00:01:55,320
So now let's configure genius 3 and do the integration so I'm going to startup genius 3 in windows in

16
00:01:55,320 --> 00:02:05,080
this case because I'm using the genius 3 VM it boots up so you can see my VM is booting up it's now

17
00:02:05,080 --> 00:02:13,300
successfully booted up and genius 3 then tells me I can create a project someone to call this NPM 1

18
00:02:16,500 --> 00:02:25,110
now to integrate the NPM virtual machine with genius 3 I need to go to edit preferences in genius 3

19
00:02:26,640 --> 00:02:34,200
and I'm going to select VM where VM is because I'm using VM wi workstation rather than virtual box I'm

20
00:02:34,200 --> 00:02:44,010
going to click new and in the VM list I can see my NPM virtual machine I'm going to click finish and

21
00:02:44,010 --> 00:02:54,580
now I'm going to click edit go to network and check this option allowed genius 3 to use any configured

22
00:02:54,580 --> 00:03:05,150
VM way adapter I'm going to leave other settings at their defaults and click okay and click Okay so

23
00:03:05,150 --> 00:03:14,570
what I've now done is integrated NPM with genius 3 and I can bold a topology consisting of Rodders and

24
00:03:14,570 --> 00:03:23,120
NPM in the next few videos I'm going to show you how to integrate genius 3 and NPM.

25
00:03:23,120 --> 00:03:31,820
Now in this example I'm using the genius 3 VM because it's the recommended way of running genius 3 it

26
00:03:31,820 --> 00:03:40,930
also makes sense in this example because I'm running NPM on a Windows 7 VM within VM where workstation.

27
00:03:40,930 --> 00:03:49,970
So I've got both NPM running and windows and genius three running within the genus 3 VM within VM where

28
00:03:49,960 --> 00:03:58,890
workstation the initial topology that we're going to build consists of three routers connected via serial

29
00:03:59,040 --> 00:04:06,620
interfaces and we'll advertise right between these writers using each or P will also configure an out

30
00:04:06,620 --> 00:04:16,110
of band management network and connect NPM to the outer band ethernet network to allow NPM to manage

31
00:04:16,110 --> 00:04:21,680
to the writers so to bolt our genius 3 topology.

32
00:04:21,970 --> 00:04:26,160
I'm going to drag three routers to the workspace

33
00:04:30,480 --> 00:04:38,450
as well as Dragon Ethernet switch to the workspace and I'm going to run to these in the genius three

34
00:04:38,450 --> 00:04:38,990
VM

35
00:04:42,360 --> 00:04:48,540
I'll cable up the routers using the serial interfaces

36
00:04:56,460 --> 00:05:07,230
so connect the rudders via their serial interfaces I'll zoom in and let's view the interface labels

37
00:05:09,990 --> 00:05:18,250
serial zero is connected to serial zero on write a to serial zero and write a one is connected to serial

38
00:05:18,250 --> 00:05:31,080
zero on Rider 2 serial 0 1 is connected to serial 0 0 on Route 3 will also connect first Ethan it interfaces

39
00:05:31,650 --> 00:05:39,940
on each rotted to the Ethernet switch this is gonna be used for our management network

40
00:05:48,980 --> 00:06:02,040
so there are interfaces on the switch and interfaces on the routers I'll now bring NPM into the topology

41
00:06:04,210 --> 00:06:11,800
and I'm going to connect that via the Ethan it interface to port for on the Ethernet switch

42
00:06:14,940 --> 00:06:23,130
so this allows NPM to manage the rod is using the outer band management network I'll configure the routers

43
00:06:23,430 --> 00:06:30,030
with IP addresses on the serial interfaces first and enable routing and then I'll configure the management

44
00:06:30,030 --> 00:06:30,690
interface.